A good rule of thumb is to allow 100W for each LED fixture so in this case, the 600W dimmer can handle only six LED fixtures. If you are meeting all of the electrical requirements of the dimmer and you are still having flicker issues, you can try adjusting the low-end trim.
Do you need a specific dimmer switch for LED lights?
Use dimmers designed for LEDs
The simple answer is to use only those dimmers that have been designed for LED loads.
What happens if you overload a dimmer switch?
Overloading your dimmer with excess wattage can also result in buzzing and humming. Change the bulbs: Buzzing coming from the fixture itself is usually related to bulb filaments.
Can you have 2 dimmers one light?
With a standard single-pole dimmer, a single switch controls the light. With a three-way dimmer, you can control a light with two switches. You will need a three-way dimmer and a three-way switch. This lets you dim from one location and turn the lights on and off from another.
How many lights can I put on one switch?
Some light fixtures, such as lamps and ceiling fan lights, use multiple bulbs and draw more power. Most circuits in a home allow for 15 to 20 amps, so you can safely connect 1400 to 2400 watts of lighting on one light switch. That’s enough for 23 to 40 60-watt bulbs or 280 to 480 5-watt LEDs.
What type of dimmer switch do I need for LED lights?
The type of dimmer switch and it’s minimum/maximum load range will indicate the compatibility with LED light bulbs. Trailing edge dimmers work best with LED light bulbs and leading-edge dimmers work best with traditional incandescent and halogen light bulbs.
What kind of dimmer switch do I need for LED lights?
Generally speaking, you will be looking for either 600 watt max load or 1000 watt. When choosing dimmers for dimmable LEDs or CFLs, you should not load a dimmer higher than approximately 25% of the rated load for the dimmer.
How hard is it to put in a dimmer switch?
Installing a dimmer switch is just as easy as installing a single-pole switch, and adjustable overhead lighting is a great improvement that adds appeal to any home.
What wattage do I need for a dimmer switch?
You should select a dimmer based upon your wattage requirements. The easiest way to do this is to add up the total wattage of the bulbs you wish to control. For example, a fixture with four 60W bulbs has a total wattage of 240. You can use a 600W dimmer to control this.
Do dimmer switches cause fires?
The most common fire caused by dimmer switches is putting too much power through them. … The reason dimmer switches get hot is fairly simple. Some dimmers get hotter than others because of their design. Old dimmer switches typically were rheostats that varied the amount of voltage going to the light bulbs.
Can any light be dimmable?
Most light fixtures will work with standard dimmer switches, including those with halogen and incandescent lamps. LED fixtures, for instance, may work with standard dimmers, but some may need a specialized dimmer. … Likewise, not all compact fluorescent (CFL) light fixtures can be dimmed.
What does 2 way dimmer switch mean?
Two way dimming allows you to dim a light fixture from two locations. You can’t use ordinary rotary dimmer switches to do this because you could potentially dim the light down to 10% with one dimmer, then walk over to the other dimmer and attempt to dim the light to below 0%.
Are all LED lights dimmable?
The short answer: it depends. Not all LED lights are dimmable, so you need to check two things to be sure. … These are designed to work with a high wattage, so they don’t work for low wattage LED bulbs. You’ll need to replace this dimmer with a trailing edge dimmer, which is designed to work with low voltage LED lights.
How many amps do LED lights use?
When Dave connects incandescent bulbs to an amp meter, they draw up to 1.6 amps, but when LED lights are used, they only pull about . 26 amps. The difference is significant, especially for RVers who do a lot of dry camping.
Can you put two lights one switch?
You can do this light switch wiring in one of two ways. The most common is to daisy-chain the light fixtures by connecting them to each other and hooking the first one up to the switch. The other way to wire multiple lights to one switch is to connect all of them directly to the switch in a “home run” configuration.
How many downlights can I have on one circuit?
the wiring rules … allocates 0.5A per lighting point; so only 20 lights can be connected to a 10A circuit.