Your question: Do I need a special flasher for LED lights?

The reason most mechanical flashers can’t work with LEDs is that LEDs need a small amount of current flow, not enough to heat the internal strip and open the circuit. Many cars also have turn signals in their side mirrors to avoid drivers’ blinds spots.

Will LED flasher work with regular bulbs?

Compatibility: All LED flashers from CEC, including the Solid State flashers, are compatible for use with regular bulbs as well as LED bulbs or a mix of LED / regular bulbs. There are many cheap LED flashers on the market that will simply go up in smoke when you put regular bulbs in.

Do I need a relay for LED indicators?

When you fit LED indicators you adjust the wattage of the system and therefore need a new relay to suit (Or fit resistors).

What is an LED flasher?

LED flashers are semiconductor integrated circuits used to turn on and off groups of light emitting diodes either sequentially or according to a programmed pattern. They are found in circuits used as indicators and controllers, as well as in home-built projects.

IT IS INTERESTING:  You asked: Are LED lights brighter than CFL?

Hyperflashing is when the turn signals blink faster than your stock incandescent bulbs did. This happens because your new LED bulbs draw such little power that your turn signal relay sees the bulbs as being out. Hyperflashing is when the turn signals blink faster than your stock incandescent bulbs did.

Is Hyper Flash illegal?

Hyper flashing is commonly associated with the problems of having LED lights for your blinkers. … Typically, hyper flashing is regarded as when your blinkers are flashing around 105-115 times per minute. This will cause a variety of issues for other drivers on the road and may even be illegal.

Do LED turn signals need a load equalizer?

LED bulbs are more efficient than incandescent bulbs and consume less power. … A Load Equalizer is required for each incandescent turn signal lamp that is replaced by an LED experiencing ‘bulb-out’ or ‘hyper-flash’ warnings.

What resistor do I need for LED turn signals?

Of course high current flow is what you are trying to be rid of… hence the LED signals. Adding a resistor to make the flasher work is adding load. It would need to be about 6 ohms and able to soak up at least 20 watts (size of a BIG cigar).

What resistor do I need for LED indicators?

Basics: Picking Resistors for LEDs

Power Supply Voltage LED Color Resistor (rounded)
4.5 V Red, Yellow, or Yellow-Green 39 Ω
4.5 V Blue, Green, White, or UV 51 Ω
5 V Blue, Green, White, or UV 68 Ω
5 V Red, Yellow, or Yellow-Green 150 Ω
IT IS INTERESTING:  Question: Does Samsung a71 have led notification light?

Is led Hyper Flash bad?

Will it screw up anything? No, not really. The real downside to hyperflash (other than annoyance to other drivers) is you may get unwanted extra attention from LEOs. Also, hyperflash is generally above 120 flashes per minute, so it would be outside of DOT regulations.

What is a LED flasher relay?

The LED flasher unit is a solid state electronic device that is specifically designed for use on vehicles fitted with LED lights. … Additionally, the flasher relay has the unique ability to control the flash rate of the vehicles LED directional indicators.

How do you make an LED flasher circuit?

How to Make LED Flasher Circuit Using BD139 Transistor

  1. Step 1: Take All Components As Shown Below. Components required – …
  2. Step 2: Circuit Diagram. This is the circuit diagram of this project. …
  3. Step 3: Connect 4.7uf Capacitor. …
  4. Step 4: Connect 2200uf Capacitor. …
  5. Step 5: Connect LED to the Circuit. …
  6. Step 6: Connect 1K Resistor. …
  7. Step 7: Connect Power Supply Wire.

How do you stop LED lights from blinking fast?

Replace the regular flasher by an LED one. This should clear the flashing error.

How can I make my LED flash slower?

Most circuits use resistors to control LED blink rate. Once you find where the resistors that control the blink rate are located, you can adjust the resistors’ value for a slower blink rate. Obtain the schematic of the LED flasher circuit you want to stop the LEDs from blinking too fast.

IT IS INTERESTING:  Do LED lights cost a lot of electricity?
Spotlight