Wiring a white LED strip (or any other strip of single-colour LEDs) couldn’t be easier. Simply connect your 240V mains supply (+ve and -ve cables) to the input terminals of your LED transformer, and connect your LED strip’s starter-lead (+ve and -ve again) to the transformer’s output terminals.
How do I connect an LED strip to my power supply?
When hardwiring the strips, you will just need to make solid connections between all your strip wires to the output wires on the power supply. This can be done with wire nuts or wiring all strips to a common positive and negative wire so you can make a one to one connection with the hardwired power supply.
How do I connect my leds strip to my mains?
To get your strip light working, connect the transformer / driver to the strip light ( extending the cable with 2 core flex if necessary). Then you connect your transformer / driver to the mains via a plug or direct to the mains and you’re away.
Can LED strip lights be hardwired?
Hardwired System. This is a hardwired system using a dimmable hardwired transformer, compatible wall switch dimmer, custom in-wall cable, and our flexible LED strips. Measure available space for flex: The first step in any system is to determine how much flexible LED strips you will need to complete your system.
What voltage do LED strip lights use?
Step 1: Determine the LED strip voltage
The majority of LED strips available on the market run at 12V DC. Others are primarily at 24V DC.
Can you connect LED strips together?
The easiest way to connect two LED strips together is to use a LED light strip connecting clip. Two LED strips can be joined with each other using a male to male clip. … You can use these connectors to connect two strips together or even connect your LED strip to the power supply.
Do you need a transformer for LED strip lights?
All mains powered LED bulbs require a transformer. Depending on the bulb type, the transformer/driver may be built in to the bulb casing or may be located externally.
How do you connect LED Strip to 12V battery?
First, press the power button on the battery and ensure that the 12V output is selected. Then, simply plug in one end of the DC cable into the battery port marked “DC output.” Then, plug the other end into the barrel jack end of the LED strip. That’s it!
Can LED strips catch fire?
The worst thing that can happen is the LED Strip can get very hot and begin to burn whatever it is fixed to, if it is a flammable surface such as timber, the outcome can be disastrous. … The other problem is running too much LED Strip linked together, or on under-rated wire or cable, this can also post a Fire Risk.
How many LED strip lights can be connected?
Vetco recommends, as a general rule, not to connect more than three complete strips end-to-end without adding in extra, higher gauge power wire or additional power supply units down the line.
What power supply do I need for LED strip?
Make sure the total wattage of your LED strip lighting is at least 20 percent less than the power supply’s rated wattage. For example, if you have an LED strip light that requires 80 watts of power to run, you’ll need a power supply that’s rated for at least 96 watts.
Do I need a resistor for LED strip?
In addition to the LEDs, one or more current limiting resistors is also necessary to ensure that the LED strip does not go into overcurrent mode. The resistor is also placed in series with the LEDs, and its resistance value is calculated such that it will draw approximately 3 volts as well.
Do LED lights work on AC or DC?
In most applications LEDs are driven by a DC power supply. LEDs consume DC current to produce light; with AC current the LED will only be lit when current flow is in the proper direction. AC applied to an LED will cause it to blink on and off, and at high frequency the LED will appear to be lit continuously.
How do I know what voltage my LED is?
How to find voltage and current of LED
- The easiest way is to look it up in the datasheet.
- You could find the LED voltage by using a multimeter with diode function.
- You could connect a battery to the LED and a potentiometer. Start with a high resistance on the potentiometer and gradually decrease it until you have an nice brightness.
17 авг. 2015 г.